Conbextra EP 10 BD Price

Moisture insensitive epoxy resin injection material.Dusk Technology

Uses

Conbextra EP 10 is a two part epoxy resin system for grout ing gaps ranging from 0.25mm to 9mm. It is an all liquid system consisting of a base and hardener.

Advantages

• Moisture insensitive
• Low creep characteristics
• High compressive, tensile and flexural strengths
• Fast, convenient pumping with early strength gain
• Withstands a wide range of chemicals

Exotherm

All epoxy systems will develop a temperature rise on mixing. Its extent will be a function of the volume to surface ratio, the ambient temperature as well as the mass and thermal conduct trinity of the surrounding materials. Contact Dusk Technology for specific data on each product.

Application instructions

Prepare the surface and seal the cracks with a sealing com pound which can also be used for bonding injection nipples. Depending on the crack width and depth the distance between nipples should be 200 to 500 mm.

Mixing and placing

Pour all the contents of the hardener pack into the base con tainer. Mix using a slow speed power mixer for 60 seconds. Use a suitable pressure pump for injecting the material into cracks. After 24 hours remove the nipples and seal the holes or voids with more sealing the compound and allow to cure.Conbextra EP 10 BD Price

Technical support

Dusk Technology offers a comprehensive range of high performance, high quality concrete repair and construction products. In addition, Dusk Technology offers technical support service to specifiers, end-users and contractors, as well as on-site technical assistance in locations all over the country.

Properties

The following results are typical for the hardener grout at 30 deg.C. For filling cracks of more than 10mm and using as an epoxy mortar
Conbextra EP 10 has to be mixed with clean graded quartz sand from 1:3 to 1:6 parts by weight depending on the consistency required. Mixing can be done with a paddle fitted to a drilling machine.

Cleaning

All tools and equipment should be cleaned immediately after use with Nitoflor Sol. Spillages should be absorbed with sand or sawdust and disposed in accordance with local regulations.

Chemical resistance

Conbextra EP 10 is resistant to oil, grease, fats, most chemicals, mild acids and alkalis, fresh and sea water.

Limitations
Temperature

During application

Grouting may be carried out without special precautions at ambient temperatures from 50 to 350C.

In service

The cured material is suitable for use from 00C.

Estimating

Packaging

Conbextra EP 10 : 1.5 litre packs

Storage

All Conbextra EP 10 products has a shelf life of 12 months in unopened container under normal warehouse conditions.
Precautions

Health and Safety

Conbextra EP 10 : Contains resins which may cause sensitisation by skin contact. Avoid contact with skin and eyes and inhalation of vapor. Wear suitable protective clothing, gloves and eye/face protection. Barrier creams provide additional skin protection. Should accidental skin contact occur, remove immediately with a resin removing cream, followed by soap and water. Do not use solvent. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical
attention immediately – do not induce vomiting.

Fire

Nitoflor Sol is flammable. In the even of fire extinguish with CO2 or foam.

Flash point : 330C

Keep away from sources of ignition – no smoking. Wear suit able protective clothing, gloves and eye/face protection. Use only in well ventilated area.

Additional information

The Fosroc range of associated products include high strength cementitious, epoxy grout, polyester resin based mortar for rapid presetting of steel shims to level or for direct bedding of small base plates; Resin Anchoring systems for same day anchoring of bolts in drilled holes in concrete or rock. Also available a range of products for use in construction; viz., ad mixtures, curing compounds, release agents, flooring systems and repair mortars. Separate datasheets are available on these products.Conbextra EP 10 BD PriceDusk TechnologyFacebook page